Project APPROVAL
Here is a list of project status that you have submitted.
Their status are provided
New projects submission have been closed.
A fine of of 100 RS per student will be charged for late comers .
| Project Name | Section | Group Member 1 | Group Member 2 | Group Member 3 | Circuit Description | Status |
| Automatic-Railway-Gate-Controller | A | Hafiz Ahsan Nawaz Khan | Sikandar Ali | Arslan Pasha/Umer Farooq | APPROVED, but you need to change circuit | |
| water level indicator | A | Ali Abid | Muhammad Danish | The Water Level Indicator employs a simple mechanism to detect and indicate the water level in an overhead tank or any other water container. The sensing is done by using a set of nine probes which are placed at nine different levels on the tank walls (with probe 9. | ATTACH MOTOR AS WELL APPROVED |
|
| line following robot | A | HUMAIRA ASLAM | SHAHID NOOR | HOREB EDWARD | This circuit describe a simple line following robot which a you can easily make in IC that is L293D and few more commonly known components like LDR and LED | APPROVED |
| laser alarm security | A | amna muzaffar | SUBMIT FULL ITEMS | |||
| Rain sensor | B | AHTASHAM ALI | FAIZAN | AHMAD RIAZ | SUBMIT FULL ITEMS | |
| Dark detector | A | Abid Hussain | Umad Ali | Darkness detector is simply a LDR (Light Dependent Resistor) interfaced square wave generator. In this project the square wave generator is developed as a 555 Timer IC based ASTABLE MULTIVIBRATOR. | SUBMIT | |
| dark detecting light | b | tamjeed hur | abdul rehman | ali raza | DISCUSS IN OFFICE | |
| Dark Sensor | A | Ali Nawaz | M. Rehan | Moeez Mazhar | Here is my new simple Electronics project about Automatic Street Light Control System or Dark Sensor.
it is a simple and powerful concept , which uses transistor ( BC 547 NPN) as a switch to switch ON and OFF the street light system automatically . it automatically switches OFF lights when Sunlight fall on it ( e.g in morning ) , by using a sensor called LDR (Light Dependent Resistor) which senses the light just like our eyes. |
good for two people or add one more thing |
| Traffic Signals | A | Ahsan Tariq Majeed | Rida Shahid | Khair un Nisa | approved | |
| Electronic Eye | A | M Raees ul Hassan | Aqib ishaq | Riyast Ali | Electronic eye has much use in this electronic age, also Known as magic eye. It can be used as an automatic guest indicator at the door, if fitted on the bottom of the door entrance. Once it is installed at the door there is no need to install a call bell. It can also be used at homes or in banks as a burglar alarm. | approved |
| Rain water alarm | B | Nida Mumtaz | Zoha Akram | Arooba Alam | Water is a conductor of electricity.When water falls on circuit. Circuit will be activated and it produce a sound | approved |
| Fire Alarm | A | Muhammad Zia Ur Rehman | Syed Muhammad Ahsan | Burhan Ahmed Babar | Thermistor, Diod, Resistor (2), capacitor, BJT, Buzzer and Vcc | approved but with motor |
| water level alarm | b | amna shahid | ayesha hameed | asma pervaiz | approved | |
| LED beat box | A | Muhammad Abdullah | Umair Iftikar | when we let sound wave as an input LEDs dance and hiphop as the flowing amplitude. | approved | |
| water boat | b | haris jamil | sulman hassn bhatti | M.waqar yousaf | approved but with extended circuit | |
| Water Level Alarm Using 555 Timer Circuit | A | Minahil Asif | Hamza Zahid | In this project, we are using a water level alarm using simple and low cost hardware using a 555 timer circuit. The aim of this project is to make a water level detecting alarm with simple and low cost hardware without compromising on the performance of the device. | approved | |
| pop corn tune with transistors of darlington pair | B | Muhammad Huzaifa | Danyal Mustafa Khan | Produce tune and use as a amplifier | approved | |
| Simple Blinking LED | B | Syed Taimoor Asghar | Usama Nasir | Zunair Prince | A very simple circuit that you can build to blink or flash LEDs. The circuit is built using transistors, resistors, capacitors, and LEDs. We will also need breadboard, wire jumpers, and a power source. | DISCUSS IN OFFICE |
| Clap Switch | B | Malik Shaharyar | Muhammad Ahmad | Muhammad Ahmed | Clap Switch Components Resistors R1=15KΩ, R5,R6=1.5KΩ?R2,R11,R12=2.2MΩ, R13=2.2KΩ?R3=270KΩ, R4=3.3KΩ?R7,R8=10KΩ, R9,R10=27KΩ?Capacitors?C1=1000µf/16v?C2=.01µf,C3,C4=.047µf?Semi Conductors?Q1,Q2,Q3= BC548?D2,D3,D4= IN 4148?D1,D5=IN 4007, Q4=BC368?Misc?T1=12v/500mA Transformer?Mic= Condenser Microphone?K1= 12V Relay, B1= Bulb or Load |
DISCUSS IN OFFICE |
| production of free energy with out using any fuel / cheap energy production system | B | Ammar liaqat (HEAD) | Hamza zahid | munim raza khan | The circuit consists of : PC FAN Strong para-magnets light bulb (1-1.5 volts) … when PC FAN and light bulb is connected to each other , our circuit is ready ! when we brought strong para-magnets close to PC-FAN it will start rotating at a specific cycle speed .in the result , bulb will start glowing, the maximum output of this circuit is (1-1.5 Volts) |
approved |
| Simple Mobile Jammer Circuit | A | Syed Ibtesam Hassan | Asad Javed | • If you understand the above circuit, this circuit analysis is simple and easy. For any jammer circuit, remember that there are three main important circuits. When they are combined together, the output of that circuit will work as a jammer. The three circuits are • RF amplifier. • Voltage controlled oscillator. • Tuning circuit. • So the transistor Q1, capacitors C4 & C5 and resistor R1 constitute the RF amplifier circuit. This will amplify the signal generated by the tuned circuit. The amplification signal is given to the antenna through C6 capacitor. Capacitor C6 will remove the DC and allow only the AC signal which is transmitted in the air. |
approved | |
| cell fone detector | A | MUHAMMAD BILAL | approved |
First published on fatsup.wordpress.com ↗